Elrs 433MHz Rx Microelectronic Receiver Module Suitable for Fpv Remote Control Drone

Product Description

ELRS 433MHz RX Microelectronic Receiver Module Suitable For FPV Remote Control Drone

BelinRC ELRS-433-RX The high-frequency head is a new generation of remote control

wireless system developed based on the open-source project ExpressLRS. The ELRS system

has the characteristics of long remote control distance, stable connection, low latency,

high refresh rate, and flexible configuration.

 

1, Basic parameters

Frequency Band: (433MHz version/360-560Mhz optional)

Output power: 100mW/250mW/500mW/1000mW/(2000mW optional)

Refresh rate: 25Hz/50Hz/100Hz/200Hz

Input Voltage: 5-12V(2S)

Main control IC: ESP32+SX1278, backpack chip ESP8285

 

2, Basic configuration

By default, the ELRS-433-TX high-frequency head only accepts signals from the Crossfire

Serial Data Protocol (CRSF). The high-frequency head interface of the remote control

needs to support CRSF signal output. The following takes the OpenTX remote control

system as an example to illustrate how to configure the remote control to output CRSF

signals and use the LUA script to control the ELRS high-frequency head.

3, CRSF protocol

In OpenTX, select MODELSELECTION to enter the MODELSETUP page, where you can turn

Internal RF off (set to OFF), enable External RF, and set Output Mode to CRSF. This is shown

in the figure below.

 

If the ELRS-433-TX high-frequency head is connected correctly, and the remote control is

configured as the CRSF output of the external high-frequency head (External RF) according

to the above, the ELRS high-frequency head can be used normally in principle.

 

4,LUA script manipulation

If you want to modify the power and refresh rate of the ELRS high-frequency head,

you need to use the LUA script of the OpenTX system. It is shown below.

Copy the official LUA script ELRS.lua to the SD card of the remote control, the path is

Scripts/Tools;

On the OpenTX system, press and hold the SYS button (e.g., RadioMaster T8 remote

controller, etc.) or the MENU button (e.g., Frsky Taranis X9D remote controller, etc.) to

enter the SD-HC CARD interface, select the ELRS.lua script and run the script on the

interface

If the LUA script runs successfully, the following figure shows the page.

 

Using the LUA script, you can choose to configure parameters such as Rate, Ratio, and

Power. The following table describes all LUA script features.

Note: The official LUA script ELRS.lua can be downloaded from the ELRS support website

(see More Information section at the URL).

5, Alignment

The factory firmware of the ELRS high-frequency head uses the ExpressLRSV3.5.0 official

version of the protocol, and there is no binding phrase set. Therefore, the linking receiver

must also be V3.0.0~V3.5.0, and the linking password has not been set.The ELRS high frequency head enters the matching state. Use the LUA script and select

Bind. The ELRS high frequency head enters the matching state. See the "LUA Script

Manipulation" section for details.

6,Power setting

ELRS high-frequency head currently support 100 mw / 250 mw / 500 mw / 1000 mw/(2000 w) is

optional.

ELRS high-frequency head transmission Power switch to use LUA scripts, choose the Power, can be in

100 mw / 250 mw / 500 mw / 1000 mw / 2000 mw (optional) switch directly. See "LUA Script

Manipulation"

Specifications: Output Power Options: 100mW, 250mW, 500mW, 1000mW, 2000mW Frequency Band: 433MHz (360-560MHz optional) Refresh Rate: 25Hz, 50Hz, 100Hz, 200Hz Input Voltage: 5-12V (2S) Main Control IC: ESP32+SX1278, backpack chip ESP8285 Compatibility: Designed for drones and FPV systems Features: **Advanced Connectivity and Control** The Mini ELRS 433TX Transmitter is a high-frequency head module that offers a powerful and reliable connection for your drone or FPV system. With a frequency band ranging from 433MHz to 560MHz, this transmitter ensures a strong and stable signal that can reach up to 360-560 meters, depending on the frequency band selected. The module is equipped with a robust main control IC, featuring the ESP32+SX1278 and ESP8285 backpack chip, which provides exceptional performance and reliability. **Versatile and User-Friendly Configuration** The Mini ELRS 433TX Transmitter is designed to be user-friendly and versatile, catering to a wide range of drone and FPV applications. By default, the transmitter accepts signals from the Crossfire Serial Data Protocol (CRSF), which is a common protocol in the remote control world. The module's interface is compatible with CRSF signals, making it a breeze to set up with various remote controls, including the OpenTX system. The LUA script manipulation feature allows users to customize the power and refresh rate settings, ensuring optimal performance for different flight scenarios. **Effortless Integration and Compatibility** The Mini ELRS 433TX Transmitter is engineered for seamless integration with various drone and FPV systems. Its compact size and lightweight design make it an ideal choice for both recreational and professional applications. The module's compatibility with a wide range of remote controls, including OpenTX, ensures that it can be easily paired with your existing setup. Whether you're a seasoned drone enthusiast or a beginner looking to enhance your FPV experience, this transmitter module is an essential addition to your gear.