| Customization: | Available |
|---|---|
| Transport Package: | Carton |
| Specification: | 6*5*5 |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Specifications | |
| Product Name | SpeedyBee F405 V330x30 Flight Controller |
| MCU | STM32F405 |
| IMU(Gyro) | BMI270 |
| USB Port Type | Type-C |
| Barometer | Built-in |
| oSD Chip | AT7456E chip |
| BLE Bluetooth | Supported.Used for Flight Controller configuration |
| DJI Air Unit Connection Way | Two ways supported:6-pin connector or direct soldering. |
| Blackbox MicroSD Card Slot | Supported.Please use ≤4GB SDSC/SDHC microSD card and should be formatted to FAT16/FAT32 format.Don't use SDXC cards.Note:Betaflight can only recognize 4GB max. |
| BetaFlight Camera Control Pad | Yes(CC pad on the front side) |
| Current Sensor Input | Supported.For SpeedyBee BLS 50A ESC,please set scale =386 and Offset =0. |
| Power Input | 3S-6S Lipo(Through G,BAT pins/pads from the 8-pin connector or 8-pads on the bottom side) |
| 5V Output | 9 groups of 5V output,four +5V pads and 1 BZ+pad(used for Buzzer)on front side, and 4x LED 5V pads.The total current load is 2A. |
| 9V Output | 2 groups of 9V output,one +9V pad on front side and other included in a connector on bottom side.The total current load is 2A. |
| 3.3V Output | Supported.Designed for 3.3V-input receivers.Up to 500mA current load. |
| 4.5V Output | Supported.Designed for receiver and GPS module even when the FC is powered through the USB port.Up to 1A current load. |
| ESC Signal | M1-M4 on bottom side and M5-M8 on front side. |
| UART | 5 sets(UART1,UART2,UART3,UART4(For ESC Telemetry),UART6) |
| ESC Telemetry UART | R4(UART4) |
| I2C | Supported.SDA&SCL pads on front side.Used for magnetometer,sonar,etc. |
| Traditional Betaflight LED Pad | Supported.5V,G and LED pads on bottom of the front side.Used for WS2812 LED controlled by Betaflight firmware. |
| Buzzer | BZ+and BZ-pad used for 5V Buzzer |
| BOOT Button | Supported [A].Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode,this is for firmware flashing when the FC gets bricked. [B].When the FC is powered on and in standby mode,the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default,short-press the BOOT button to cycle the LED displaying mode.Long- press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode.Under BF-LED mode,all the LED1-LED4 strips will be controlled by Betaflight firmware. |
| RSSI Input | Supported.Named as RS on the front side. |
| SmartPort | Not supported |
| Supported Flight Controller Firmware |
BetaFlight(Default),EMUFlight,INAV |
| Firmware Target Name | SPEEDYBEEF405V3 |
| Mounting | 30.5×30.5mm(4mm hole diameter) |
| Dimension | 41.6(L)x39.4(W)x7.8(H)mm |
| Weight | 9.6g |
){kind=link}